We have found this article pertaining to How to Install a Bathtub Yourself listed below on the net and reckoned it made sense to share it with you on this page.
Installing a tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably difficult job. If the old bathtub is conveniently accessible, the project can relocate easily; if you have to open a wall to eliminate the old bathtub and also position the new tub, the task is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the new one. Make sure you have qualified yourself for the task as well as fit trying it. Instead of employing a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your restroom if you have actually currently acquired a brand-new bathtub and also do not require to change the arrangement of your previous supply of water pipelines.
Your devices and also material list should comprise the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wood boards under its feet, place the bath tub in the required setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub up until the level reads level.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the bath tub needs to wait up until the bathtub has been made use of a minimum of when as this will resolve it right into its final placement.
Getting ready for the Installment
Firstly, the sustaining structure provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall between the bath and the tiling, leading to difficulties with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Make feedback down the page. We would be glad to see your opinion about this blog post. Hoping that you visit us again in the near future. Feel free to set aside a second to share this blog posting if you appreciated it. Thank-you for your time spent reading it.
Pricing